dog-box-transmission[/caption]Dog ring gearbox explained!
Almost all road cars have a synchromesh gearbox but many race race cars have a dog ring gearbox. Why, and what is the difference?
Changing gear works by sliding different gears up and down shafts. This engages different gears to allow different combinations and produce different overall gear ratios.
In a dog ring gearbox there is no synchromesh to even out the difference in speed between one gear and another. Synchromesh gears have a collar or cone that works like a clutch and as the two gears move towards each other the friction between the cones causes the gears to rotate at the same speed. The small dog teeth then engage to lock the two gears together.
In a dog ring gearbox the gears do not have this cone which causes the synchronisation of gear speeds. Instead the gears have fewer, much larger dog teeth which mean that gears are either fully engaged or fully disengaged. To change gear the driver has to match the speed of the gears manually by double de-clutching or by changing gear at the correct speed. To minimise wear, gear changes should be completed as quickly as possible to prevent the dog teeth clashing. The image below shows a synchromesh gear on the left and a dog ring gear on the right.
A common misconception is that dog ring gear boxes have straight cut (spur) gears. In fact both synchromesh gearboxes and dog ring gearboxes can have straight cut gears or helical gears. Straight cut gears transmit more power so they are always used for racing, but straight cut gears are very noisy which is why road cars tend to have helical gears. In the image below the top pair of gears are helical and the bottom set are straight cut or spur gears.
The advantages of having a dog ring gearbox are that gear changes can be completed very quickly by briefly blipping the throttle with minimal use of the clutch. This has obvious benefits on track because the engine will be powering the wheels for a larger proportion of time. However, dog ring gearboxes are difficult to use on the road in traffic or around town and without quick gear changes at the correct engine revs the dog teeth with wear out quickly. Synchromesh gearboxes are much easier to use, allow slower shifting and tend to last longer.
The only road legal production car with a (optional) dog ring gearbox is the Abarth 695 Biposto. The 695 Biposto is the most extreme version of the Abarth (Fiat) 500 with the 1.4 litre turbo engine tuned up to 190bhp and 250Nm of torque. The car weighs just under a tonne at 997kg and accelerates from 0-62 in 5.9 seconds. It has a carbon fibre front splitter and rear diffuser, a stripped out interior and Akrapovič exhaust. The car is rather expensive for what is essentially a tarted up Fiat 500, costing upwards of £30k. Oh, and the dog ring gearbox is an £8500 option! But if you want a stock production car with a race car gearbox, this is your only option. Check out this one for sale for £46k!
Gearbox Beatdown - Synchromesh vs. Dog Box
Before decoding synchromesh and dog gearboxes, it is critical to understand the beast. It’s all about engagement; how the gearsets are selected within the transmission is the difference between synchromesh and a dog box.
Impp 1109 01 o+gearbox beatdown+transmission
Photo 2/14 | Gearbox Beatdown - Synchromesh vs. Dog Box
Synchromesh Transmissions
Most modern cars are fitted with a synchronized engagement gearbox from the factory to deliver smooth, reliable, and quiet operation, which is paramount for a daily driven vehicle. Synchromesh transmissions operate using a collar that applies force to a cone-shaped clutch attached to the gear. The collar allows the shaft speed of the gearset and the input shaft to be matched or “synched” to the output shaft prior to the collar locking into place and initiating a shift.
Synchromesh gear engagement is best at lower engine speeds and requires a bit more time compared to a dog box, to facilitate shifts. Limitations of synchromesh gearboxes in high-performance applications include slow upshifting at very high engine speeds—e.g. 9,000 rpm—and slow downshifting, as well as the need to fully use the clutch.
Dog Box Transmissions
Dog engagement is normally used in racing applications where fast, precise shifting is needed. Dog gear engagement is facilitated by numerous large teeth (dogs) that mate into matching openings machined into the opposite surface of the drive gear. Unlike the synchro engagement, there is no synchronizing mechanism to assist in equalizing speed. Ideal gear selection—e.g. minimal clashing and wear of the dog rings—is achieved by quick shifts; the motto here is “the quicker the better”, so bang away.
Impp 1109 02 o+gearbox beatdown+gears
Photo 3/14 | Gearbox Beatdown - Synchromesh vs. Dog Box
There is no depressing the clutch in the conventional sense like with the synchromesh transmission. A momentary break in engine load until the shift is achieved by a quick throttle blip or clutch depression. The driver will then experience the dog ring engaging with the next gear and the throttle can be reapplied. With practice this can be done in milliseconds. In fact, a driver can preload the stick shift in the direction of the next shift, and then when he either blips the throttle or clutch the shifter will quickly click in the desired gear.
With all else equal, dog-engagement gears are much stronger than synchro-engagement gears because without needing to make space for synchro rings, the gears themselves can be made thicker. The number of dogs (teeth) and the size of the openings determine the window of opportunity that the dogs have to engage during the shift event. Rings with a smaller number of teeth provide a more efficient, smoother shift quality. The downsides to this easier engagement are increased noise and abruptness on the shift.
Dog Gear Don’ts
The most destructive method of shifting dog gears is attempting to change gears in a “passenger car” or “synchromesh” manner. This involves slow shifting and use of the clutch—i.e. lifting off the throttle, depressing the clutch, moving the gear lever slowly, releasing the clutch, and applying the throttle—a scenario typically found in stop-and-go traffic.
Impp 1109 03 o+gearbox beatdown+gears
Photo 4/14 | Gearbox Beatdown - Synchromesh vs. Dog Box
Straight-Cut Myth
The belief that dog boxes inherently feature straight-cut gears is a long-standing misconception. In fact, either type of gearset can be fitted with straight cut—also known as spur–gears as well as conventional helical-cut gears. The cut of the drive gear is a separate characteristic of the gearbox and does not affect the engagement of the gears.
Impp 1109 04 o+gearbox beatdown+dog box
Photo 5/14 | Gearbox Beatdown - Synchromesh vs. Dog Box
The Dog Pound
Dog engagement can be introduced to a stock gearbox by swapping gearsets. Aftermarket dog sets are usually made of higher-grade material and feature bigger, stronger teeth, and better profiles. Albins Gear, located in Australia, has moved to the forefront of the dog-box revolution, offering a wide range of dog-engagement gearsets as well as fortified synchro sets for Honda, Porsche, Nissan, Subaru, Mazda, VW, and Mitsubishi applications.
All Albins dogs feature a CAD “pent-roof” pentagon-shaped surface that deflects the dogs apart on a mis-shift, drastically extending the life of the gear. Albins dog gears are verified using a robotic CMM (coordinate measuring machine) to assure perfection with tolerances better than 0.015 mm on each and every part. Furthermore, Albins has been able to produce its own proprietary steel alloy with a consistency far superior to mass-produced, low-cost sets.
Synchromesh Versus Dog Box Gearset Comparison
Notice the thicker gears and teeth of the Albins unit (below) and the cuff that replaces Fifth gear (unneeded in the quarter-mile) and ties the two shafts together for added strength. The Albins gears and teeth are not only thicker, but they are also made from the company’s proprietary steel alloy for superior metallurgical strength.
Impp 1109 05 o+gearbox beatdown+syncromesh vs dog
Photo 6/14 | Gearbox Beatdown - Synchromesh vs. Dog Box
Cone and Dog Rings
Here is the big difference between synchro and dog boxes. The synchromesh ring (left) uses a cone that a brass clutch ring pushes against to equalize the speed between the gear and the input shaft to ease gear engagement. Once this happens, the small pointed teeth around the perimeter deflect off the engagement ring and allow the slider to engage the gear. The dogs have four large engagement teeth that drop into large windows in the slider, and can engage the gear even when spinning at a different speed than the input shaft.
Impp 1109 06 o+gearbox beatdown+cone dog rings
Photo 7/14 | Gearbox Beatdown - Synchromesh vs. Dog Box
Rings and Gears
Here we see the rings on their appropriate gear. This is how they would be installed in the transmission.
Impp 1109 07 o+gearbox beatdown+rings and gears
Photo 8/14 | Gearbox Beatdown - Synchromesh vs. Dog Box
Gears In Case
Albins gearsets drop right into the stock transmission case, delivering nearly “sequential-fast” shifts without the sequential box price tag. Albins offers dog-engagement gearsets as well as fortified synchro sets for Honda, Porsche, Nissan, Subaru, Mazda, VW, and Mitsubishi applications.
Impp 1109 08 o+gearbox beatdown+gears in case
Photo 9/14 | Gearbox Beatdown - Synchromesh vs. Dog Box
SpeedFactory’s Outlaw-class Civic has been a rolling 1,100-whp gearset cruncher. It has competed up and down the West Coast and as far east as Englishtown. Its best efforts to date are 8.89 at 172 mph and 8.92 topping out at 179 mph, and Albins gearsets have contributed greatly to its reliability and consistency.
Impp 1109 09 o+gearbox beatdown+speed factory
Photo 10/14 | Gearbox Beatdown - Synchromesh vs. Dog Box
Gearset Savior
SpeedFactory Bulletproofs The B-Series Transmission
SpeedFactory Racing has developed an innovative modification for B-series hydraulic transmissions that eliminates inherent problems in the mechanism, avoiding the “speed shift blues” in street cars and race cars alike.
Impp 1109 10 o+gearbox beatdown+shift change holder assembly
Photo 11/14 | Gearbox Beatdown - Synchromesh vs. Dog Box
The Shift Change Holder Assembly (SCHA) is the problem child. Located inside the transmission case, the SCHA is the mechanism that actually moves the shift forks into position, engaging each gear as it’s selected via the stick shift. SpeedFactory modifies the SCHA in seven different areas to withstand the rigors of hard shifting in standard synchromesh or dog-engaged transmissions.
The stock shift change arm is the weakest link of the SCHA. The stock arm is made of low-quality stamped steel and over time is susceptible to stress cracks or bending when speed shifted. SpeedFactory replaces the stock arm with a heavy-duty, heat-treated arm CNC-machined from tool steel that will not bend or break.
The interlock piece is also a potential problem. SpeedFactory installs a brand-new OEM interlock, braces it, and performs some polishing/profile mods to endure the abuse of repeated power shifts, be it on the street or at the track in a drag racing application.
Finally, the shift select return spring has been upgraded with a much stronger unit. This gives the shifter a more positive feel, and returns the shifter to the center position with authority.
Beyond fortifying the transmission against breakage, the SpeedFactory SCHA also adds efficiency to the shifting process, especially the 2-3 shifts. Just push the shifter forward, and it will automatically drop into Third gear. It pulls the shifter to the center position with speed and precision to help eliminate the dreaded 1-2-1 or 2-3-2 gear mis-shifts.
The SpeedFactory improvements have been thrash tested on the company’s wicked 1,100-whp, 8.89-second Outlaw Civic with great success, ensuring more consistent shifts, lower e.t.’s, and saved transmissions for weekend warriors and hard-shifting, real-world street drivers alike.
The SpeedFactory modified SCHA (right) has a CNC’d tool steel shift change arm (with SF logo). Also, note the beefier return spring of the SpeedFactory piece at the far left.
Impp 1109 11 o+gearbox beatdown+speedfactory scha
Photo 12/14 | Gearbox Beatdown - Synchromesh vs. Dog Box
SpeedFactory also welds the baseplate in several places for added strength and rigidity, and to prevent stress fractures. The custom SCHA will save transmissions by ensuring proper engagement in less than ideal shift scenarios.
Impp 1109 12 o+gearbox beatdown+baseplate
Photo 13/14 | Gearbox Beatdown - Synchromesh vs. Dog Box
SCHA Rear Buttress
Note the buttressing between the baseplate and the spring pad. This is just one of the seven different modifications SpeedFactory makes to the SCHA to ensure happy gear slamming.
Impp 1109 13 o+gearbox beatdown+buttress
Photo 14/14 | Gearbox Beatdown - Synchromesh vs. Dog Box
No comments:
Post a Comment